Hancock Racing
12-10-2005, 11:17 PM
Saleen 91-0088 Canvertible was taken apart for complete restoration. While the car was down we were gathering parts as many of you know. I contacted many people looking for the items we needed. I had most of the things we needed and some low life broke into our shop and stole a lot of parts including some engine parts as well as a turbo and other items that were in that shop. I am including a complete list of missing parts both Saleen and other wise so please if anyone hears of anything let me know. These items were taken from the Americus GA area.
Thanks,
Marshall Hancock
MISSING PARTS LIST
1991 302 engine block bored 4.030 and line honed (Complete less camshaft)
Stock 1991 302 H.O. Mustang cast steel crankshaft (turned .010 on the main journals and .010 on the rod journals)
(New) Eagle 5.090 length Forged Connecting Rods part number SIR5090FP
(New) JE Forged Pistons 1.600 compression height with wrist pins part number 131656
(New) Complete set of 4.030 Total Seal piston rings (1/16 - 1/16 - 3 /16 ring package) part number TSR-T3690-30
A pair of 1969 351 Windsor Cylinder Heads complete with stainless 1.94 intake and 1.60 exhaust valves
(Hand ported and gasket matched to intake manifold **stamped RCH on the end of each head**)
(New) Canton Racing Products 7 QT 7-1/2" DEEP T-SUMP oil pan with AN 10 oil return bung welded in and two drain plugs. part number CR15640 01
(New) Turbonetics T-76 P trim turbocharger .96 A/R on center polished with V band exhaust housing
(New) SSAC Intercooler measured 24" x 12 " 3" core completely polished 3" inlet and 3" outlet
Tial 38mm Wastegate WG 38mm Assembly Polished Aluminum Finish 2 bolt design part number TIL-WGT38
(New) Turbonetics Polished Stainless Steel Godzilla Blow Off Valve part number TNT-10765
(New) Aeromotive A1000 Fuel Pump part number AEI-11101
(New) Aeromotive 2 port EFI fuel pressure regulator part number AEI-13101
Saleen Specific Parts
(NOS) Monroe Formula GP / Saleen Specific front, rear, and quad shocks (These items were brand new OEM leftover stock that I had been lucky enough to find and had just been sourced after 3 years of searching)
Saleen Mustang specific shifter boot and surround plate with Plastic Saleen Plaque that read Saleen Auto Sports 91-0088
Saleen G Load Brace
Saleen Strut Tower brace for Supercharged car
Saleen Front and rear sway bars
Saleen Black Floor Mats
(The suspension pieces listed above were black and needed to be re-powdercoated. They were all in good working condition but did show the 40k- miles that are on the car)
Less important, but still missing parts.
A pair of well used (needed rebuilding) T3 style Mustang SVO turbo's with internal wastegates (basically worthless and I had nothing invested in them)
(New) Hooker Headers for a Jeep with a 307 (these belonged to a friend and he ordered them wrong so they were just leftover)
Hand Polished stock 1991 Mustang intake hand ported to 70mm Throttle Body Inlet and gasket match ported to stock lower intake
Lower intake was gasket matched to Fel Pro gasket
Polished factory 5.0 valve covers with K&N filter on oill fill tubes
Polished Aluminum Radiator 3 core (Not sure of Manufacturer and was not in working condition. Cooling fins were bent pretty bad)
1989 and 1995 V8 Mustang Wiring Harnesses both engine and computer harness for two separate cars
2 factory Mustang Computers model numbers A9L and A9P
http://www.racingjunkrides.com/images/uploaded/2/3/432_3.jpg
Thanks,
Marshall Hancock
MISSING PARTS LIST
1991 302 engine block bored 4.030 and line honed (Complete less camshaft)
Stock 1991 302 H.O. Mustang cast steel crankshaft (turned .010 on the main journals and .010 on the rod journals)
(New) Eagle 5.090 length Forged Connecting Rods part number SIR5090FP
(New) JE Forged Pistons 1.600 compression height with wrist pins part number 131656
(New) Complete set of 4.030 Total Seal piston rings (1/16 - 1/16 - 3 /16 ring package) part number TSR-T3690-30
A pair of 1969 351 Windsor Cylinder Heads complete with stainless 1.94 intake and 1.60 exhaust valves
(Hand ported and gasket matched to intake manifold **stamped RCH on the end of each head**)
(New) Canton Racing Products 7 QT 7-1/2" DEEP T-SUMP oil pan with AN 10 oil return bung welded in and two drain plugs. part number CR15640 01
(New) Turbonetics T-76 P trim turbocharger .96 A/R on center polished with V band exhaust housing
(New) SSAC Intercooler measured 24" x 12 " 3" core completely polished 3" inlet and 3" outlet
Tial 38mm Wastegate WG 38mm Assembly Polished Aluminum Finish 2 bolt design part number TIL-WGT38
(New) Turbonetics Polished Stainless Steel Godzilla Blow Off Valve part number TNT-10765
(New) Aeromotive A1000 Fuel Pump part number AEI-11101
(New) Aeromotive 2 port EFI fuel pressure regulator part number AEI-13101
Saleen Specific Parts
(NOS) Monroe Formula GP / Saleen Specific front, rear, and quad shocks (These items were brand new OEM leftover stock that I had been lucky enough to find and had just been sourced after 3 years of searching)
Saleen Mustang specific shifter boot and surround plate with Plastic Saleen Plaque that read Saleen Auto Sports 91-0088
Saleen G Load Brace
Saleen Strut Tower brace for Supercharged car
Saleen Front and rear sway bars
Saleen Black Floor Mats
(The suspension pieces listed above were black and needed to be re-powdercoated. They were all in good working condition but did show the 40k- miles that are on the car)
Less important, but still missing parts.
A pair of well used (needed rebuilding) T3 style Mustang SVO turbo's with internal wastegates (basically worthless and I had nothing invested in them)
(New) Hooker Headers for a Jeep with a 307 (these belonged to a friend and he ordered them wrong so they were just leftover)
Hand Polished stock 1991 Mustang intake hand ported to 70mm Throttle Body Inlet and gasket match ported to stock lower intake
Lower intake was gasket matched to Fel Pro gasket
Polished factory 5.0 valve covers with K&N filter on oill fill tubes
Polished Aluminum Radiator 3 core (Not sure of Manufacturer and was not in working condition. Cooling fins were bent pretty bad)
1989 and 1995 V8 Mustang Wiring Harnesses both engine and computer harness for two separate cars
2 factory Mustang Computers model numbers A9L and A9P
http://www.racingjunkrides.com/images/uploaded/2/3/432_3.jpg