The Saleen Forums at soec.org header image

Go Back   The Saleen Forums at soec.org > Vendors > Vendor Ads & Group Buys
Register FAQ Members List Calendar Mark Forums Read

Vendor Ads & Group Buys Vendors can post ads and group buys here, as well as questions pertaining to the advertised products. Postings for items which infringe upon Saleen intellectual property or trademarks will be removed.

Reply
 
Thread Tools Display Modes
  #1  
Old 11-27-2012
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default Brand New Part Alert: 2 Piece Cross Drilled / Slotted Zinc Coated Rotors

Tired of warpped rotors? Tired of brake fade? Want to decrease your drivetrain horsepower loss?

We've had many request for upgraded rotors for the 05-Current Saleen. We are proud to announce we have worked along side Baer Brake Systems and have developed an exclusive rotor for the ST-40 Caliper. These will ONLY be available through 281 Motorsports and will be completed in production now in about 10 working days as of the status check today. These rotors will be a direct replacement for the factory 1 or 2 piece slotted rotors you have now.

Here are some of the advantages of a 2 piece rotor:

Lighter rotor (huge weight reduction) than original one-piece rotor – meaning lower spinning weight equaling more of the vehicle horsepower getting planted on the ground, better pad wear and tire wear. If it turns on your vehicles power, your losing horsepower.
Cooler disc - due to higher heat dissipation rate of aluminum hat as compared to cast iron 1 piece
Ability to replace only the rotor ring, while reusiing the hat. Although the initial cost of two-piece rotors is higher than one-piece rotors, the lifetime operating cost could be lower.

281 Motorsports Exclusive / Baer EradiSpeed +2 Saleen ST40 Rotor Upgrade Features:
EradiSpeed™ rotors feature premium high silicon content iron castings.
Rotor plates or outer rotor surfaces are cast with additional mass to absorb additional heat.
Internal curved and directional vanes maximize air flow and cooling.
Externally slotting and drilling alleviate friction losses from pad outgassing and a zinc chromate surface finish resists rust.
Counter rotational application of slots and holes further resists pad transfer and balance issues associated with patterns which run in the conventional direction of rotation.
Each gas relief hole drilled in an EradiSpeed rotor is located directly behind an internal vane and chamfered appropriately.
These details coupled with Baer’s material selection virtually eliminate durability concerns associated with drilling mere mortal rotors.


Pricing for 14" complete two-piece rotors, clear zinc coated, slotted and cross drilled is $749.99. Matching Rear 14" rotors with caliper relocation brakets also available.

Available Options:
Silver Zinc Wash
Custom Colored Anodized Hats (center section)
Cyro Treating to dramatically decrease warping (recomended for weekend track warriors)

Introductory Group Buy Pricing for first 10 orders: $649.99! Save $100 and buy NOW! Order the matching rear (normally $649.99) or save $75 when ordering them with the group buy.

1. Terry N. - Full Set
2. KC Childs - Full Set
3. seethrough - Full Set
4. cdmsaleen - Fronts
5. Bird Dog 36 - Fronts
6.
7.
8.
9.
10.

We also have 99-04 "Saleen Brembo" caliper 2 piece rotors available for front and rear. Call for details on this setup.
Attached Thumbnails
281 Motorsports-Saleen-2 piece rotor-img.jpg  

Attached Images
 
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"

Last edited by Jason @ 281m; 12-04-2012 at 11:15 PM.
Reply With Quote
  #2  
Old 11-27-2012
seethrough seethrough is offline
Senior Saleen Forums Participant
 
Join Date: Apr 2009
Location: Chatham, IL
Posts: 809
Default

Sign me up for front and rear.
Reply With Quote
  #3  
Old 11-27-2012
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by seethrough View Post
Sign me up for front and rear.
Give me a hollar and we'll get your order going!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #4  
Old 11-27-2012
cdmsaleen cdmsaleen is offline
SOEC Member
 
Join Date: Jul 2008
Location: Orange County, Calif.
Posts: 110
Default

Put me down for a pair of the fronts & thank you for another job well done!
__________________
06-1008 S/C
Tungsten Gray with Scenic Roof
Completely rebuilt from top to bottom
Reply With Quote
  #5  
Old 11-27-2012
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by cdmsaleen View Post
Put me down for a pair of the fronts & thank you for another job well done!
Will do Mark!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #6  
Old 11-27-2012
kendoo130's Avatar
kendoo130 kendoo130 is offline
Senior Saleen Forums Participant
 
Join Date: Oct 2009
Location: Long Island NY
Posts: 210
Default

Hey Jason-any plans for a 15" version for us Extreme owners?
__________________
http://i568.photobucket.com/albums/s...rivewaypic.jpg
06-141E 1 of 3
Reply With Quote
  #7  
Old 11-27-2012
cdmsaleen cdmsaleen is offline
SOEC Member
 
Join Date: Jul 2008
Location: Orange County, Calif.
Posts: 110
Default

Quote:
Originally Posted by Jason @ 281m View Post
Will do Mark!
Jason-pm sent
__________________
06-1008 S/C
Tungsten Gray with Scenic Roof
Completely rebuilt from top to bottom
Reply With Quote
  #8  
Old 11-28-2012
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by kendoo130 View Post
Hey Jason-any plans for a 15" version for us Extreme owners?
Yes, absolutely! If we have several interested parties, we'll make them!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #9  
Old 11-30-2012
Barricade's Avatar
Barricade Barricade is offline
SOEC Member
 
Join Date: Jul 2009
Location: Texas
Posts: 1,744
Default

I slotted only cheaper?
__________________
-ǝsınƃsıp uı ʇoqoɹ-
BARRICADE 643
06-108E
Reply With Quote
  #10  
Old 12-01-2012
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by Barricade View Post
I slotted only cheaper?
Honestly, slightly more. They run these in productions, so to special order it, it would cost a few bucks more. But yes, it can be done.
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #11  
Old 12-03-2012
Red6 Red6 is offline
Saleen Forums Participant
 
Join Date: May 2012
Location: Dana Point, CA
Posts: 87
Default

Jason-

Could I get the rears in two piece cross drilled only? I want a two piece rear rotor to match my front cross drilled rotors. PM me please with pricing/timeline.

Thanks

Paul
Reply With Quote
  #12  
Old 12-03-2012
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Paul,

Yes, we can custom order them...shoot me a call for pricing/availability - we avoid doing busines through pm's.

Quote:
Originally Posted by Red6 View Post
Jason-

Could I get the rears in two piece cross drilled only? I want a two piece rear rotor to match my front cross drilled rotors. PM me please with pricing/timeline.

Thanks

Paul
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #13  
Old 12-04-2012
Red6 Red6 is offline
Saleen Forums Participant
 
Join Date: May 2012
Location: Dana Point, CA
Posts: 87
Default

Quote:
Originally Posted by Jason @ 281m View Post
Paul,

Yes, we can custom order them...shoot me a call for pricing/availability - we avoid doing busines through pm's.
Awesome. I'll talk to once my rear covers are ready.
Reply With Quote
  #14  
Old 12-04-2012
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by Red6 View Post
Awesome. I'll talk to once my rear covers are ready.
Paul, your caliper covers are done! We are picking up our load of stuff in the next day or two, we'll get them going.

Just spoke to Baer, our custom rotor hat production schedule in pending in the coming days. It shouldnt be long before they ship! We are pretty excited to have these available!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #15  
Old 12-04-2012
Bird Dog 36's Avatar
Bird Dog 36 Bird Dog 36 is offline
Saleen Forums Participant
 
Join Date: Aug 2012
Location: Brighton, CO
Posts: 10
Default I'm In!

Jason,
I'll take a set of fronts please. Let me know what you need to get the ball rolling.

Thanks,

Jay
Reply With Quote
  #16  
Old 12-04-2012
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by Bird Dog 36 View Post
Jason,
I'll take a set of fronts please. Let me know what you need to get the ball rolling.

Thanks,

Jay
Hey Jay,

Shoot me an email with your perticulars and ill get your order ready, then give me a call with your moolah info.
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #17  
Old 12-22-2012
Bird Dog 36's Avatar
Bird Dog 36 Bird Dog 36 is offline
Saleen Forums Participant
 
Join Date: Aug 2012
Location: Brighton, CO
Posts: 10
Default Shipping yet?

Hey Jason,

Any info on when my units will be shipping out? I just received my CC bill, and was reminded what a great salesman you are.

Happy Holidays to All!
Reply With Quote
  #18  
Old 12-23-2012
07s281sc's Avatar
07s281sc 07s281sc is offline
SOEC Member
 
Join Date: Nov 2011
Location: San Diego
Posts: 137
Default

Quote:
Originally Posted by kendoo130 View Post
Hey Jason-any plans for a 15" version for us Extreme owners?
If you're looking for a big brake option Might also want to consider the 2013 Gt500 brake setup. Massive 6 piston monoblock brembos w/15" rotors. This is the route I'm going but will be powdercoating the calipers Saleen red and adding 2 piece rotors.
http://www.s197forum.com/forum/showthread.php?t=85230
__________________
2007 S281sc-437 Rwhp/433 Torque
Saleen SuperShaker w/ 3.6 pulley and custom tune, Magnaflow X pipe w/cats, Corsa Mufflers, BMR Lcas, GT500 fuel pumps, AFCO Heat Exchanger, Chin spoiler, Saleen lower mesh grill, MGW shifter, 2010 Saleen shift knob, UPR Catch Can, UPR Tensioner, V10 Water Pump Pulley, LED Lighting, HIDs

Last edited by 07s281sc; 12-23-2012 at 01:47 AM.
Reply With Quote
  #19  
Old 01-09-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Just got off the phone with Baer again, they should be shipping to us on friday and we should have them within 1-2 days. So we should be shipping all the orders next week. Thanks everyone!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #20  
Old 01-09-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

UPDATE: (from an hour ago, lol) brakes are shipping tomorrow morning truck freight. We should still see them on monday. However the production cost going forward after the pre-buy will be much higher due to the actual production cost of these. The new price will be $998 per pair. We will post some pictures as soon as we get a set on the two cars that ordered them in the shop.
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #21  
Old 01-10-2013
XxBoostinxX's Avatar
XxBoostinxX XxBoostinxX is offline
SOEC Member
 
Join Date: Jun 2011
Location: Hoover, AL
Posts: 1,638
Default

Quote:
Originally Posted by Jason @ 281m View Post
UPDATE: (from an hour ago, lol) brakes are shipping tomorrow morning truck freight. We should still see them on monday. However the production cost going forward after the pre-buy will be much higher due to the actual production cost of these. The new price will be $998 per pair. We will post some pictures as soon as we get a set on the two cars that ordered them in the shop.
When does the preorder end Jason? I am working on it on my end about getting a full set. Give me another day and I'll give you a call.
__________________
Black - 06-1279 - S281SC
Reply With Quote
  #22  
Old 01-16-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Hey guys, we got them in from Baer on Monday and test fit them before we shipped them and there was a small clearance issue. Baer has them back now and it should only be a few days to get them corrected. Hang tight, we'll update you asap.
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #23  
Old 01-17-2013
purevnm's Avatar
purevnm purevnm is offline
Senior Saleen Forums Participant
 
Join Date: Jun 2011
Location: Omaha, Ne
Posts: 114
Default

Quote:
Originally Posted by Barricade View Post
I slotted only cheaper?
I can't remember what I paid for them but they can make them slotted only to match the fronts on the Extremes:
BEFORE


AFTER:
Reply With Quote
  #24  
Old 01-17-2013
Werecow Werecow is offline
SOEC Member
 
Join Date: Mar 2009
Location: Santa Maria, Ca
Posts: 1,826
Default

Jason,

Is it possible to take existing rotors and have them zinc coated?
Reply With Quote
  #25  
Old 01-17-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Its $50 more for the custom order....its what Baer charges.

Quote:
Originally Posted by purevnm View Post
I can't remember what I paid for them but they can make them slotted only to match the fronts on the Extremes:
BEFORE


AFTER:
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #26  
Old 01-17-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by Werecow View Post
Jason,

Is it possible to take existing rotors and have them zinc coated?

Yes, of course! Im sure you can find someone local or we can have them done for $20 each.
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #27  
Old 01-17-2013
o6Saleen E o6Saleen E is offline
Account with Invalid Email
 
Join Date: Dec 2008
Location: Miami Lakes
Posts: 267
Default

I already have this set for over two years Jason and it is a very good upgrade.

Quote:
Originally Posted by Jason @ 281m View Post
Tired of warpped rotors? Tired of brake fade? Want to decrease your drivetrain horsepower loss?

We've had many request for upgraded rotors for the 05-Current Saleen. We are proud to announce we have worked along side Baer Brake Systems and have developed an exclusive rotor for the ST-40 Caliper. These will ONLY be available through 281 Motorsports and will be completed in production now in about 10 working days as of the status check today. These rotors will be a direct replacement for the factory 1 or 2 piece slotted rotors you have now.

Here are some of the advantages of a 2 piece rotor:

Lighter rotor (huge weight reduction) than original one-piece rotor – meaning lower spinning weight equaling more of the vehicle horsepower getting planted on the ground, better pad wear and tire wear. If it turns on your vehicles power, your losing horsepower.
Cooler disc - due to higher heat dissipation rate of aluminum hat as compared to cast iron 1 piece
Ability to replace only the rotor ring, while reusiing the hat. Although the initial cost of two-piece rotors is higher than one-piece rotors, the lifetime operating cost could be lower.

281 Motorsports Exclusive / Baer EradiSpeed +2 Saleen ST40 Rotor Upgrade Features:
EradiSpeed™ rotors feature premium high silicon content iron castings.
Rotor plates or outer rotor surfaces are cast with additional mass to absorb additional heat.
Internal curved and directional vanes maximize air flow and cooling.
Externally slotting and drilling alleviate friction losses from pad outgassing and a zinc chromate surface finish resists rust.
Counter rotational application of slots and holes further resists pad transfer and balance issues associated with patterns which run in the conventional direction of rotation.
Each gas relief hole drilled in an EradiSpeed rotor is located directly behind an internal vane and chamfered appropriately.
These details coupled with Baer’s material selection virtually eliminate durability concerns associated with drilling mere mortal rotors.


Pricing for 14" complete two-piece rotors, clear zinc coated, slotted and cross drilled is $749.99. Matching Rear 14" rotors with caliper relocation brakets also available.

Available Options:
Silver Zinc Wash
Custom Colored Anodized Hats (center section)
Cyro Treating to dramatically decrease warping (recomended for weekend track warriors)

Introductory Group Buy Pricing for first 10 orders: $649.99! Save $100 and buy NOW! Order the matching rear (normally $649.99) or save $75 when ordering them with the group buy.

1. Terry N. - Full Set
2. KC Childs - Full Set
3. seethrough - Full Set
4. cdmsaleen - Fronts
5. Bird Dog 36 - Fronts
6.
7.
8.
9.
10.

We also have 99-04 "Saleen Brembo" caliper 2 piece rotors available for front and rear. Call for details on this setup.
__________________
06Saleen E (#86)
Reply With Quote
  #28  
Old 01-23-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Hey guys,....THESE ARE NOW IN STOCK AND READY TO SHIP!!!!!!!!!! 20% off all Stop Tech pads for orders place by 1/25/13. Can you say....SEXY?? By the way our rotors are also 1/8" thicker as well making them way stronger than the stock rusty rotors on there now.











__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"

Last edited by Jason @ 281m; 01-23-2013 at 07:08 PM.
Reply With Quote
  #29  
Old 01-23-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Picture of the rears...

__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #30  
Old 01-23-2013
seethrough seethrough is offline
Senior Saleen Forums Participant
 
Join Date: Apr 2009
Location: Chatham, IL
Posts: 809
Default

Thanks Jason. Did the preorders ship out?
Reply With Quote
  #31  
Old 01-24-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by seethrough View Post
Thanks Jason. Did the preorders ship out?
They are boxed, tagged and ready for pickup!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #32  
Old 01-24-2013
seethrough seethrough is offline
Senior Saleen Forums Participant
 
Join Date: Apr 2009
Location: Chatham, IL
Posts: 809
Default

Mocked up the new rear rotors today. Wow what an improvement. I still need to paint the rear caliper but I will do that once the front rotors come in and I swap the front calipers for the powdercoated set I have. I have to send out a big thanks to 281 Motorsports - this is one of the best cosmetic upgrades that I have done to the car. (I haven't gotten to drive it yet to see how they perform so I will comment on that later). The tiny rusty rear rotors where a real eyesore. This is such an amazing improvement. I can't wait for the fronts to arrive. Thanks again Jason for working out all the details on this and for your attention to detail. A+ vendor in my opinion. Here are a few shots I took comparing the old to the new.

Old rotor layed over the new rotor for size comparison:

New rotor installed:

New rotor w/ wheel

Old rotor w/ wheel

A step back with new rotor:

A step back with old rotor:
Reply With Quote
  #33  
Old 01-24-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Thanks for the comment! But lets know forget about the performance benefits of those for the rear! Going from a 10.85" to a whopping 14"! Then since its a 2-piece with an aluminum hat (center) it will disapate heat way better and then the obvious benefit of cross drilling, slotting and zinc washing. The biggest performance difference of the brake caliper location adds significance leverage to increase massive amounts of clamping power!

Quote:
Originally Posted by seethrough View Post
Mocked up the new rear rotors today. Wow what an improvement. I still need to paint the rear caliper but I will do that once the front rotors come in and I swap the front calipers for the powdercoated set I have. I have to send out a big thanks to 281 Motorsports - this is one of the best cosmetic upgrades that I have done to the car. (I haven't gotten to drive it yet to see how they perform so I will comment on that later). The tiny rusty rear rotors where a real eyesore. This is such an amazing improvement. I can't wait for the fronts to arrive. Thanks again Jason for working out all the details on this and for your attention to detail. A+ vendor in my opinion. Here are a few shots I took comparing the old to the new.

Old rotor layed over the new rotor for size comparison:

New rotor installed:

New rotor w/ wheel

Old rotor w/ wheel

A step back with new rotor:

A step back with old rotor:
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #34  
Old 01-25-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Hey Guys n Gals,

Just to let you know, we need to close the group buy. We will close both on Tuesday to give you a few days to get your order in.

Thanks everyone! FREE 281 Hats to all who post pictures up when they've installed them!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #35  
Old 06-24-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default Summer Sale

Hey Guys,

Lets start off the summer right with keeping our brakes cooler! Our first summer sale will be our rotors normally $995, we will offer them at $729.99 until the end of the month!

Those of you who post pictures of them installed on your car will get a FREE 281 Flex fit hat!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #36  
Old 06-25-2013
seethrough seethrough is offline
Senior Saleen Forums Participant
 
Join Date: Apr 2009
Location: Chatham, IL
Posts: 809
Default

I reorganized my photobucket account and it looks like it disrupted my posts with pictures. Here is a repost;

old rotor over new


new installed


new w/wheel


old w/wheel


a step back w/ old


a step back w/ new
Reply With Quote
  #37  
Old 06-25-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Seethough,

I thought you did fronts as well? Did we ever get your hat out?
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #38  
Old 06-25-2013
seethrough seethrough is offline
Senior Saleen Forums Participant
 
Join Date: Apr 2009
Location: Chatham, IL
Posts: 809
Default

Did do the fronts as well but I don't have pictures of them yet. Still need to repaint the front calipers before I take any. Haven't seen a hat yet.
Reply With Quote
  #39  
Old 06-25-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by seethrough View Post
Did do the fronts as well but I don't have pictures of them yet. Still need to repaint the front calipers before I take any. Haven't seen a hat yet.
Post those front pics and you will! Lol
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #40  
Old 06-30-2013
hazmat's Avatar
hazmat hazmat is offline
Senior Saleen Forums Participant
 
Join Date: May 2011
Location: Deer Park, Texas
Posts: 215
Default

****, I can't believe I missed the group buy on this.

Jason, what kind of a package deal will you make me on front & back set?
__________________

2006 S281SC #1113 with JDM 550 HP kit

1995 Cobra #1221 598"BBF w/ Twin 88s
Reply With Quote
  #41  
Old 06-30-2013
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by hazmat View Post
****, I can't believe I missed the group buy on this.

Jason, what kind of a package deal will you make me on front & back set?
Give me a call tomorrow, we'll hook you up!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #42  
Old 02-27-2014
OneQwkStang's Avatar
OneQwkStang OneQwkStang is offline
SOEC Member
 
Join Date: May 2011
Location: Ontario, Canada
Posts: 1,266
Default

Bump..want front and rear rotors pads....
Reply With Quote
  #43  
Old 02-28-2014
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Tired of warpped rotors? Tired of brake fade? Want to decrease your drivetrain horsepower loss?

We've had many request for upgraded rotors for the 05-Current Saleen. We are proud to provide these amazing rotor that we have worked along side Baer Brake Systems and have developed these exclusive rotors for the ST-40 Caliper. These will ONLY be available through 281 Motorsports. Once the group buy is completed and all deposits are in, production will take about 10 working days. These rotors will be a direct replacement for the factory 1 piece slotted rotors you have now.

Here are some of the advantages of a 2 piece rotor:

Lighter rotor (huge weight reduction) than original one-piece rotor – meaning lower spinning weight equaling more of the vehicle horsepower getting planted on the ground, better pad wear and tire wear. If it turns on your vehicles power, your losing horsepower.
Cooler disc - due to higher heat dissipation rate of aluminum hat as compared to cast iron 1 piece
Ability to replace only the rotor ring, while reusiing the hat. Although the initial cost of two-piece rotors is higher than one-piece rotors, the lifetime operating cost could be lower.

281 Motorsports Exclusive / Baer EradiSpeed +2 Saleen ST40 Rotor Upgrade Features:
EradiSpeed™ rotors feature premium high silicon content iron castings.
Rotor plates or outer rotor surfaces are cast with additional mass to absorb additional heat.
Internal curved and directional vanes maximize air flow and cooling.
Externally slotting and drilling alleviate friction losses from pad outgassing and a zinc chromate surface finish resists rust.
Counter rotational application of slots and holes further resists pad transfer and balance issues associated with patterns which run in the conventional direction of rotation.
Each gas relief hole drilled in an EradiSpeed rotor is located directly behind an internal vane and chamfered appropriately.
These details coupled with Baer’s material selection virtually eliminate durability concerns associated with drilling mere mortal rotors.


Pricing for 14" complete two-piece rotors, clear zinc coated, slotted and cross drilled is $998.99. Matching Rear 14" rotors with caliper relocation brakets also available.

Available Options:
Silver Zinc Wash
Custom Colored Anodized Hats (center section)
Cyro Treating to dramatically decrease warping (recomended for weekend track warriors)

Group Buy Pricing for first 5 orders: $698.99! Save $300 and buy NOW! Order the matching rear (normally $699.99) or save $50 when ordering them with the group buy. We will offer a 15% to SOEC members on any brake pads you order while ordering your rotors.

1. Oneqwkstang
2. 06Saleen
3.
4.
5.
Attached Thumbnails
IMAG0395.jpg  

Attached Images
   
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"

Last edited by Jason @ 281m; 03-04-2014 at 12:04 PM.
Reply With Quote
  #44  
Old 03-04-2014
06Saleen's Avatar
06Saleen 06Saleen is offline
Saleen Forums Participant
 
Join Date: Jul 2008
Location: Las Vegas
Posts: 34
Default

Jason I will take a set of fronts and pads.
Reply With Quote
  #45  
Old 03-04-2014
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by 06Saleen View Post
Jason I will take a set of fronts and pads.
Awesome! Give us a call and we'll enter your order!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #46  
Old 05-28-2014
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by OneQwkStang View Post
Bump..want front and rear rotors pads....
Order processed.
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #47  
Old 05-28-2014
06Saleen's Avatar
06Saleen 06Saleen is offline
Saleen Forums Participant
 
Join Date: Jul 2008
Location: Las Vegas
Posts: 34
Default

Will give you a call tomorrow about order
Reply With Quote
  #48  
Old 05-28-2014
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
SOEC Member
 
Join Date: Mar 2010
Location: Placentia, California
Posts: 4,586
Default

Quote:
Originally Posted by 06Saleen View Post
Will give you a call tomorrow about order
Perfect, I was trying to figure out your name....lol. The screen names vs. real names can get difficult. Send me an email with your name and ill get your paperwork started.
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2002 Saleen Speedster #02-346
2007 Roush TrakPak-Race car
2015 Mustang GT

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: sales@281m.com
Web: www.saleenspeedlab.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #49  
Old 05-28-2014
OneQwkStang's Avatar
OneQwkStang OneQwkStang is offline
SOEC Member
 
Join Date: May 2011
Location: Ontario, Canada
Posts: 1,266
Default

Quote:
Originally Posted by Jason @ 281m View Post
Order processed.
Sent you emails...
Reply With Quote
  #50  
Old 05-28-2014
Barricade's Avatar
Barricade Barricade is offline
SOEC Member
 
Join Date: Jul 2009
Location: Texas
Posts: 1,744
Default

Anything on sale Jason...?
__________________
-ǝsınƃsıp uı ʇoqoɹ-
BARRICADE 643
06-108E
Reply With Quote
Reply

Bookmarks

Tags
mustang, s281, saleen brakes, saleen extreme, saleen rotors

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 12:20 AM.




Orders placed through these advertiser links help to support SOEC and this website.

Tire Rack Wheel Clearance

When you buy one Valeo® ULTIMATE™ Wiper Blade from Tire Rack, you'll get one free!

Dunlop $50 Rebate


| SOEC.ORG | ABOUT SOEC | MEMBERSHIP | MERCHANDISE | LITERATURE | VEHICLE PRODUCTION | SALEEN AUTOMOTIVE | CONTACT SOEC | SOEC @ FACEBOOK |


All Original Content Copyright © 1991-2019 Saleen Owners and Enthusiasts Club, LLC (SOEC). All Rights Reserved.
SOEC is the official independent, non-profit organization for owners and enthusiasts of vehicles by Steve Saleen and Saleen Automotive, Inc.