|
Register | FAQ | Members List | Calendar | Mark Forums Read |
2005-2009 Saleen Mustang For all S281, S302, H281 and H302 models based on the Ford S-197 Mustang platform, with the exception of the S302 PJ (see below). Be sure to specify year, model and equipment if asking for help. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Q: Idler pulley options? - Series VI
Okay I did a quick search and didn't find a thread on this so here goes. I'm looking to upgrade the pulleys on my car. I run the v-10 water pump pulley, mosaleen system and would like to replace the pulleys with units from thump racing. Just curious with out going out an measuring everything what sizes I will need and how many of each. Is there a kit for a Saleen SC'd car?
__________________
2007 Shelby GT, Saleen SC Stage 3 with 3.0 pulley,mosaleen tensioner sys. UCA,LCA,BMR A arm Brace, SVE Dark Stainless 18x10's, Nitto NT05's, MGW Shifter, Pypes LT's with off-road X pipe, Bassani Axle backs, FRP 3.73's,BMR Watts Link, Steeda shaft loop, JLT 110mm CAI, FRP valve Covers, Brenspeed tuned. 12.425@114.63 4800 feet on Nitto 555's. Latest dyno is 492hp/463tq. |
#2
|
||||
|
||||
There should only be two idler pulleys you need. The pulley before the PS pulley (90mm) and the pulley in the alternator bracket (76mm). I tried a Thump idler for the alternator bracket pulley and it was too wide and would require clearancing the bracket. I ended up with billet aluminum Metco pullies.
__________________
|
#3
|
|||
|
|||
The plastic one w/ Saleen supercharger kit is notorious for having the bearing seize up and snap a belt. Good call to update . Shameless plug to new modders I have a belt, V10 water pump pulley , and Mosaleen system for sale super cheap. All new and never installed . PM me
|
#4
|
||||
|
||||
Quote:
__________________
2007 Shelby GT, Saleen SC Stage 3 with 3.0 pulley,mosaleen tensioner sys. UCA,LCA,BMR A arm Brace, SVE Dark Stainless 18x10's, Nitto NT05's, MGW Shifter, Pypes LT's with off-road X pipe, Bassani Axle backs, FRP 3.73's,BMR Watts Link, Steeda shaft loop, JLT 110mm CAI, FRP valve Covers, Brenspeed tuned. 12.425@114.63 4800 feet on Nitto 555's. Latest dyno is 492hp/463tq. |
#5
|
||||
|
||||
Got an email from Rick at Metco and he suggested the 1.5" 90mm idler pulley instead of the 1" (6rib). Can anyone confirm getting ready to place an order.
Thanks
__________________
2007 Shelby GT, Saleen SC Stage 3 with 3.0 pulley,mosaleen tensioner sys. UCA,LCA,BMR A arm Brace, SVE Dark Stainless 18x10's, Nitto NT05's, MGW Shifter, Pypes LT's with off-road X pipe, Bassani Axle backs, FRP 3.73's,BMR Watts Link, Steeda shaft loop, JLT 110mm CAI, FRP valve Covers, Brenspeed tuned. 12.425@114.63 4800 feet on Nitto 555's. Latest dyno is 492hp/463tq. |
#6
|
||||
|
||||
Quote:
Not sure why he wants you to use the wider pulley, but it shouldn't be a problem in that location. It becomes a problem if it's the pulley behind the alternator bracket.
__________________
|
#7
|
||||
|
||||
Thanks for the info.
__________________
2007 Shelby GT, Saleen SC Stage 3 with 3.0 pulley,mosaleen tensioner sys. UCA,LCA,BMR A arm Brace, SVE Dark Stainless 18x10's, Nitto NT05's, MGW Shifter, Pypes LT's with off-road X pipe, Bassani Axle backs, FRP 3.73's,BMR Watts Link, Steeda shaft loop, JLT 110mm CAI, FRP valve Covers, Brenspeed tuned. 12.425@114.63 4800 feet on Nitto 555's. Latest dyno is 492hp/463tq. |
#8
|
||||
|
||||
update on my pulley replacement. The Metco pulleys arrived one 76 and one 90. However since I'm running the Mosaleen system I actually needed two 76mm. So I'll be sending the 90 back and getting another 76. For those running a similar system and a 3.0 pulley /v-10 water pump you cannot run a 106 inch belt. It will not work. 106.5 is the smallest you can use.
__________________
2007 Shelby GT, Saleen SC Stage 3 with 3.0 pulley,mosaleen tensioner sys. UCA,LCA,BMR A arm Brace, SVE Dark Stainless 18x10's, Nitto NT05's, MGW Shifter, Pypes LT's with off-road X pipe, Bassani Axle backs, FRP 3.73's,BMR Watts Link, Steeda shaft loop, JLT 110mm CAI, FRP valve Covers, Brenspeed tuned. 12.425@114.63 4800 feet on Nitto 555's. Latest dyno is 492hp/463tq. |
#9
|
||||
|
||||
If someone needs a 106 inch Gates Racing Belt let me know. I'll sell it for $40 shipped saves you a few bucks off of what Rock Auto will charge. Here is the part number K061054RB. PM me if you want it
https://www.rockauto.com/en/moreinfo...860784&jsn=233
__________________
2007 Shelby GT, Saleen SC Stage 3 with 3.0 pulley,mosaleen tensioner sys. UCA,LCA,BMR A arm Brace, SVE Dark Stainless 18x10's, Nitto NT05's, MGW Shifter, Pypes LT's with off-road X pipe, Bassani Axle backs, FRP 3.73's,BMR Watts Link, Steeda shaft loop, JLT 110mm CAI, FRP valve Covers, Brenspeed tuned. 12.425@114.63 4800 feet on Nitto 555's. Latest dyno is 492hp/463tq. Last edited by tbrock; 04-30-2016 at 07:17 PM. |
#10
|
||||
|
||||
sent the belt back to rock auto for a refund
__________________
2007 Shelby GT, Saleen SC Stage 3 with 3.0 pulley,mosaleen tensioner sys. UCA,LCA,BMR A arm Brace, SVE Dark Stainless 18x10's, Nitto NT05's, MGW Shifter, Pypes LT's with off-road X pipe, Bassani Axle backs, FRP 3.73's,BMR Watts Link, Steeda shaft loop, JLT 110mm CAI, FRP valve Covers, Brenspeed tuned. 12.425@114.63 4800 feet on Nitto 555's. Latest dyno is 492hp/463tq. |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|