The Saleen Forums at soec.org header image

Go Back   The Saleen Forums at soec.org > Saleen Mustang Discussions > 2005-2009 Saleen Mustang
Register FAQ Members List Calendar Mark Forums Read

2005-2009 Saleen Mustang For all S281, S302, H281 and H302 models based on the Ford S-197 Mustang platform, with the exception of the S302 PJ (see below). Be sure to specify year, model and equipment if asking for help.

Reply
 
Thread Tools Display Modes
  #1  
Old 07-18-2018
jtotheROC jtotheROC is offline
Saleen Forums Participant
 
Join Date: May 2013
Location: Barrie, ontario, canada
Posts: 48
Default Q: Meth injection, anyone else doing it?

Just had this baby installed, IAT's no longer an issue. Just need to get it tuned and see what the gains could be.

Anyone else try this?
Reply With Quote
  #2  
Old 07-20-2018
seelye76's Avatar
seelye76 seelye76 is offline
SOEC Member
 
Join Date: Mar 2010
Location: Brimfield, IL
Posts: 868
Default

I use water/meth injection. I have the Snow Stage 3 with the 2.5 gal tank in my trunk. I would caution you not to get too aggressive with your tune in regards to AF correction. You are not guaranteed that each cylinder will be getting the same mixture. You will still see gains though due to lower intake temps.
__________________
Reply With Quote
  #3  
Old 07-20-2018
jtotheROC jtotheROC is offline
Saleen Forums Participant
 
Join Date: May 2013
Location: Barrie, ontario, canada
Posts: 48
Default

Okay, this is good information, I have the stage 2 from Snow.

https://www.snowperformance.net/Stag...o-2130-brd.htm

My tuner has good experience with Meth, but i think you are correct to really be safe with A/F as the dispersion may not be equal.

What kind of power gains did you see with that?

I need to find a 2.7 pulley, as with the cooler temps it could be worth to max the super charger out now. I already have innovators west H/H, thump tensioner, and Mosaleen set up.

I think Brenspeed has pulleys, need to check
Reply With Quote
  #4  
Old 07-20-2018
seelye76's Avatar
seelye76 seelye76 is offline
SOEC Member
 
Join Date: Mar 2010
Location: Brimfield, IL
Posts: 868
Default

Quote:
Originally Posted by jtotheROC View Post
Okay, this is good information, I have the stage 2 from Snow.



https://www.snowperformance.net/Stag...o-2130-brd.htm



My tuner has good experience with Meth, but i think you are correct to really be safe with A/F as the dispersion may not be equal.



What kind of power gains did you see with that?



I need to find a 2.7 pulley, as with the cooler temps it could be worth to max the super charger out now. I already have innovators west H/H, thump tensioner, and Mosaleen set up.



I think Brenspeed has pulleys, need to check


I don’t really have any specific dyno results before and after. Always others things that were changed. I’d say you’d see a little improvement on the dyno, but it’s such a short pull it doesn’t have time to heat up the intake temps like a trip down the 1320. That’s where you’ll see the difference... real world. You can log your timing and really see how it’s helping. I run E85 now so I run a bunch of timing, but still use meth/water injection to keep the intake temps down especially for 1/2 mile runs.
__________________
Reply With Quote
  #5  
Old 08-03-2018
jtotheROC jtotheROC is offline
Saleen Forums Participant
 
Join Date: May 2013
Location: Barrie, ontario, canada
Posts: 48
Default

Seelye, where is your nozzle installed? I had it on the Dyno and no difference in IAT...I'm sure it's set up right. I have the spacer after the throttle.body made by snow where it injects.
Reply With Quote
  #6  
Old 08-03-2018
seelye76's Avatar
seelye76 seelye76 is offline
SOEC Member
 
Join Date: Mar 2010
Location: Brimfield, IL
Posts: 868
Default

Quote:
Originally Posted by jtotheROC View Post
Seelye, where is your nozzle installed? I had it on the Dyno and no difference in IAT...I'm sure it's set up right. I have the spacer after the throttle.body made by snow where it injects.
I have two nozzles. 1 pre throttle body and 1 post throttle body.
__________________
Reply With Quote
  #7  
Old 09-09-2018
mosaleen's Avatar
mosaleen mosaleen is offline
SOEC Member
 
Join Date: Dec 2007
Location: Joplin, Mo.
Posts: 762
Default

Where do you get the nozzle plate , does it change the CAI placement?
__________________
2005 S/C #10 Press Car w/ Scenic Roof
3.20 S/C Pulley & 18% overdrive Crank
Mosaleen S/C no slip idler system
3:73 gears, Watts link Gen II
14" front brakes, slotted rear rotors
Brenspeed 302, 47lb inj, longtubes/ catted H-pipe 570 rwhp 545 rwtq (SAE) 13.5 lbs boost, Afco heat exchanger
F-5 Joplin Mo. Tornado surviour 5-22-11.
Reply With Quote
  #8  
Old 09-28-2018
Jason @ 281m's Avatar
Jason @ 281m Jason @ 281m is offline
Senior Saleen Forums Participant
 
Join Date: Mar 2010
Location: Fullerton, California
Posts: 4,699
Default

We run methanol quite a bit now. After much effort we have found the absolute best location to allow the meth to plume perfectly. The results were huge and IAT's plummeted. I will not share the location simply due to efforts went into figuring out its location and the complexity of the location. We will be offering installing it into the superchargers when we service them. If you buy a meth kit from us, that support will be given. But meth is a IAT savior!
__________________
Jason | 281 Motorsports

NO PM'S - PLEASE CALL | 714-575-1505

1996 Cobra Vortech SC / Track prepped
2015 Coyote Powered F-150

Check out our facility promo video here: http://bit.ly/1yHNfxM

Email: 281motorsports@gmail.com
Web: www.ProSpeedMustang.com
Facebook: www.facebook.com/mustangperformance
Youtube: http://bit.ly/1zOxanf


"Doing the job right...is the ONLY option we offer!"
Reply With Quote
  #9  
Old 10-22-2018
jtotheROC jtotheROC is offline
Saleen Forums Participant
 
Join Date: May 2013
Location: Barrie, ontario, canada
Posts: 48
Default

Nozzle plate is from SNOW and does not effect CAI placement.
Reply With Quote
  #10  
Old 03-31-2019
jtotheROC jtotheROC is offline
Saleen Forums Participant
 
Join Date: May 2013
Location: Barrie, ontario, canada
Posts: 48
Default

Sorry, I just saw this question. Snow has the nozzle plate that is after the TB. It's just a spacer.
Reply With Quote
  #11  
Old 06-16-2019
Jay2006-S281E's Avatar
Jay2006-S281E Jay2006-S281E is offline
Saleen Forums Participant
 
Join Date: Aug 2017
Location: Elk River MN
Posts: 37
Default

I’m looking to put the Killer Chiller setup on my 2006 Saleen Extreme.
https://killerchiller.com/
__________________
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 06:17 AM.


Orders placed through these advertiser links help to support SOEC and this website.

Tire Rack Wheel Clearance

When you buy one Valeo® ULTIMATE™ Wiper Blade from Tire Rack, you'll get one free!

Dunlop $50 Rebate


| SOEC.ORG | ABOUT SOEC | MEMBERSHIP | SHOWROOM | LITERATURE | VEHICLE PRODUCTION | THE SALEEN TRADER | SALEEN AUTOMOTIVE | CONTACT SOEC | SOEC @ FACEBOOK |


All Original Content Copyright © 1991-2021 Saleen Owners and Enthusiasts Club, LLC (SOEC). All Rights Reserved.
SOEC is the official independent, non-profit organization for owners and enthusiasts of vehicles by Steve Saleen and Saleen Automotive, Inc.