The Saleen Forums at soec.org

The Saleen Forums at soec.org (https://saleenforums.soec.org/index.php)
-   2007-2008 S331 Sportruck (https://saleenforums.soec.org/forumdisplay.php?f=77)
-   -   Fore Precision Triple Pump hat and Mosaleen idler (https://saleenforums.soec.org/showthread.php?t=8185)

FATHERFORD 08-23-2010 09:21 AM

Fore Precision Triple Pump hat and Mosaleen idler
 
Not sure If I have made a proper introduction on this forum...

I have a 2004 F-150 XLT regular cab with a 5.4L. It has seen many parts in it's short lifetime. Anything from a full bolt on n/a truck, vortech blower pushing 12lbs(450rwhp/450rwtq) to now it has a Saleen Blower.

Current performance mod list:
Saleen Blower
2.87 Pulley
JDM Stage 1 system(Roush Intake)
Mosaleen Idler
LS1 Camaro Electric Fans
PI 2800 converter
OBX Longtubes
OBX Resonators
"custom" true dual 2.5" exhaust running through a Magnaflow Dual in/out muffler
Fore Precision Works Triple Pump Setup(Troyer performance sells)
4.11 Gears
JDM mail order tune

I have a dynotune set on September 3rd with PSI Motorsports out of Webster, Texas. I have been trying to get one setup with JDM when SR. is down this way, but we are both very busy people and can never seem to be in the same area at the same time. No fault of theres and I have been very pleased with their mail order tune and customer service.

I have yet to see any post on this forum about the following mods I installed a few weeks ago. I'll transfer the post I did to other forums on this one for future reference by other members.

MoSaleen Idler and the Troyer/Fore Precision Works Fuel Pump Setup.

http://i331.photobucket.com/albums/l...enidler001.jpg

http://i331.photobucket.com/albums/l...uelpump001.jpg
http://i331.photobucket.com/albums/l...uelpump003.jpg
http://i331.photobucket.com/albums/l...uelpump002.jpg
http://i331.photobucket.com/albums/l...uelpump004.jpg
http://i331.photobucket.com/albums/l...uelpump005.jpg
http://i331.photobucket.com/albums/l...uelpump006.jpg

FATHERFORD 08-23-2010 09:24 AM

**I have yet been able to really finish this write up...so their might be some errors**

Overall the install was pretty straight forward ONCE I got a factory wiring diagram. This setup has NO check valves, so longer starts are normal. I am pleased so far the results of this unit. I highly suggest this install is for someone with good electrical and mechanical skills.If there are any errors in the pictures I apologize in advance.

For the install, I took off my bed. 6 bolts, 2 hoses, 3 7mm screws for the filler neck, and 2 connections out back for the lights. Don't forget to unhook the battery first. The factory FPDM is out back and the tank is located driver side center of the truck.
http://i331.photobucket.com/albums/l...01_800x600.jpg

Here you can see the attached Kenne Bell boost a pump wired into the FPDM. You will need to cut and splice into this connector later on.
http://i331.photobucket.com/albums/l...02_800x600.jpg

Before you remove anything from the tank, blow it off with high compressed air.
http://i331.photobucket.com/albums/l...03_800x600.jpg

Now you must remove the fuel lines and electrical connections. To remove lines, you must either press in completely, or pull out a tab then press in. **note** There is a line IN the tank you must unhook also.
http://i331.photobucket.com/albums/l...05_800x600.jpg

Next you will need to take off the ring that holds the assembly in place. To do this you need a screwdriver and a hammer. Don't be afraid to use some force in this process.
[IMG]http://i331.photobucket.com/albums/l...04_800x600.jpg[/IMG]
http://i331.photobucket.com/albums/l...06_800x600.jpg

Now before you do anything else, blow off the area again of any loose dirt. You will need to disconnect one line that is inside the tank. Remove carefully. (sorry no picture)

You will need transfer the fuel level float sensor from your factory unit to the aftermarket Fore Precision Work's unit. This is a simple snap on, snap off operation. Disconnect the sensor's wire, DON'T CUT. Connect the wire from the factory level sensor to the wire on the aftermarket unit and use heat shrink to ensure a tight bond between the connection. You will also need to install your fuel pumps and hook them up to the existing wires on the unit. The pump wires will only go one way so it's dummy proof. Tighten hose clamps to the pump once they are installed in the unit. You must also attach a ground wire, just remove a screw and attach(see picture).
http://i331.photobucket.com/albums/l...07_800x600.jpg
http://i331.photobucket.com/albums/l...08_800x600.jpg

Now the unit is ready to install. When installing don't forget to hook up the in-tank line that you disconnected earlier.
http://i331.photobucket.com/albums/l...09_800x600.jpg

You must also place the tab on the hat in the correct orientation. You will see an arrow on the tank(sorry no picture of arrow) Place the factory ring back on using a screwdriver and hammer.
http://i331.photobucket.com/albums/l...10_800x600.jpg

Apparently, somewhere amongst the years, ford decided to change sizes of some lines. Included in the kit is an extra piece that allows you to use either of the lines. Remove the 2.5mm alan headed screws and replace. Snap your lines back on and you are finished with the physical install of the fuel hat setup itself.
http://i331.photobucket.com/albums/l...11_800x600.jpg

**Note**This is where it will get real vague until I get some time to draw up a wiring diagram.

I installed the 2nd FPDM on the drive side frame rail near the factory FPDM. I drilled and tapped(6mm) the frame to use the supplied hardware. I also installed the two relays where the spare tires normally resides(mine has rides in my bed).
http://i331.photobucket.com/albums/l...12_800x600.jpg
http://i331.photobucket.com/albums/l...13_800x600.jpg

The two fuel pump 30amp breakers that come with the kit I mounted on the firewall with existing factory hardware. I made a small plate and bolted the breakers to it. I routed (2) 10 gauge wires from the batter to the bronze studs of the breakers. The supplied 10 gauge wire and looms travels from the "silver" stud of the breakers, through the cowl, down to the driver side frame rail to the back of the truck to the relays.
http://i331.photobucket.com/albums/l...15_800x600.jpg
http://i331.photobucket.com/albums/l...16_800x600.jpg

**continue on next post**

FATHERFORD 08-23-2010 09:25 AM

http://i331.photobucket.com/albums/l...irediagram.jpg
http://i331.photobucket.com/albums/l...irediagram.jpg

and just a picture of the fuel hat all wired up and complete..
http://i331.photobucket.com/albums/l...14_800x600.jpg

Mosaleen Idler Installed
http://i331.photobucket.com/albums/l...02_800x600.jpg

Meikol02 08-23-2010 01:04 PM

Welcome to the forum.

Nice write up and pictures. Sorry you missed Jim Sr. but you are right about being hard to find time.

The guys at PSI are pretty cool to talk to I look forward to hearing the results of your set-up.

Dave 08-23-2010 10:54 PM

Welcome to the forums! :smile:

julioclotch 11-17-2014 10:26 AM

good job, I have a harley f150 sc and put mustang gt dual fuel pump kit, I think putting 5 speed manual transmicion t3640


All times are GMT -4. The time now is 06:22 PM.