|
Register | FAQ | Members List | Calendar | Mark Forums Read |
1999-2004 Saleen Mustang For the SN-95 New Edge platform. Be sure to specify year, model and equipment if asking for help. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Q: Do I need an UD or Idler Pulley?
Hey gents whats going on,
I am somewhat of a newb with this kind of stuff so please bear with me. About 6 months ago I put bbk long tubes, bbk catted h-pipe, tunable inductions CAI, accufab TB and sct MAF on my whip with a tune for 351 RWHP. My car already had a Reichard Racing pulley with a 2.600 diameter when i purchased it. I was told after I got it tuned that it did not need an idler or under drive pulley because it would make the belt spin too fast and as a result I would lose power. My goal is to reach 400 RWHP. Can anyone elaborate on this? Also any suggestions? Please keep responses simple. I am in the learning phase. Thank for your patience and knowledge. -Chris |
#2
|
||||
|
||||
Stock bottom end?
Quote:
__________________
Jason | 281 Motorsports NO PM'S - PLEASE CALL | 714-575-1505 1996 Cobra Vortech SC / Track prepped 2015 Coyote Powered F-150 Check out our facility promo video here: http://bit.ly/1yHNfxM Email: 281motorsports@gmail.com Web: www.ProSpeedMustang.com Facebook: www.facebook.com/mustangperformance Youtube: http://bit.ly/1zOxanf "Doing the job right...is the ONLY option we offer!" |
#3
|
|||
|
|||
What do you mean by stock bottom end Jason?
|
#4
|
||||
|
||||
Does your car have a built motor (forged internals)?
__________________
Jason | 281 Motorsports NO PM'S - PLEASE CALL | 714-575-1505 1996 Cobra Vortech SC / Track prepped 2015 Coyote Powered F-150 Check out our facility promo video here: http://bit.ly/1yHNfxM Email: 281motorsports@gmail.com Web: www.ProSpeedMustang.com Facebook: www.facebook.com/mustangperformance Youtube: http://bit.ly/1zOxanf "Doing the job right...is the ONLY option we offer!" |
#5
|
|||
|
|||
no there are forged internals
|
#6
|
|||
|
|||
What year car do you have? Which supercharger is it? Series 1? Series 2?
If you're not sure then post a picture and we can tell you which one. The person that told you info is correct. Underdrive pulleys shouldn't be put on supercharged applications.
__________________
07 Porsche 911 Turbo 02 Saleen S/C Speedster 3.73 gears Chicane 66mm Pulley SCT custom tune SVT Focus Fuel Pump 13" Brembo Brakes LFP Heat Exchanger and Supertank TorkTech Intake SVT Cobra single blade TB Chicane Intercooler 42lb injectors 90mm MAF FPRP Aluminum Driveshaft Maximum Motorsports LCA's, Subframes, Torque Arm, Panhard Bar, Steering Shaft, Front Control Arms and Aluminum Rack Bushings MM Coilover kit with caster camber plates |
#7
|
||||
|
||||
Quite honestly, 350ish RWHP is the max I would recommend going. You can push that limit but your only asking for trouble.
__________________
Jason | 281 Motorsports NO PM'S - PLEASE CALL | 714-575-1505 1996 Cobra Vortech SC / Track prepped 2015 Coyote Powered F-150 Check out our facility promo video here: http://bit.ly/1yHNfxM Email: 281motorsports@gmail.com Web: www.ProSpeedMustang.com Facebook: www.facebook.com/mustangperformance Youtube: http://bit.ly/1zOxanf "Doing the job right...is the ONLY option we offer!" |
#8
|
|||
|
|||
Here are some pics of the engine
please let me know what you think
|
#9
|
|||
|
|||
You have an Eaton M90 (called the series II) supercharger on your car. With that supercharger you'll be hard pressed to get to 400 rwhp without throwing a lot of money at it. (by a lot of money I'm talking roughly the same amount of money you would need to go buy a new kenne bell supercharger and install it. it would would cost ~$5-6k and would also yield you 400 rwhp).
I'm at 400 (also with the series II) and in order to get there I had to redo the entire intake side (tork tech), new intercooler, heat exchanger, fuel pump, supertank injectors, mass airflow meter, smaller pulley and tune.
__________________
07 Porsche 911 Turbo 02 Saleen S/C Speedster 3.73 gears Chicane 66mm Pulley SCT custom tune SVT Focus Fuel Pump 13" Brembo Brakes LFP Heat Exchanger and Supertank TorkTech Intake SVT Cobra single blade TB Chicane Intercooler 42lb injectors 90mm MAF FPRP Aluminum Driveshaft Maximum Motorsports LCA's, Subframes, Torque Arm, Panhard Bar, Steering Shaft, Front Control Arms and Aluminum Rack Bushings MM Coilover kit with caster camber plates |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|